[MSNoise] Changing startdate/enddate and ref_begin/ref_end

[Marco Taruselli]

Yes, my data starts at 2018-05-24_8am and it ends at 2018-05-24_9am.

Marco Taruselli

PhD Fellow - Structural, Seismic and Geotechnical Engineering



Politecnico di Milano

Department of Civil and Environmental Engineering

Piazza L. da Vinci, 32, 20133 Milano, ITALY


Il giorno gio 30 ago 2018 alle ore 17:20 Thomas Lecocq <
Thomas.Lecocq at seismology.be> ha scritto:

> Hey,
>
> One thing: does startdate & endate "surround" the whole period? The
> CCFtime etc plots are based on startdate & enddate.
>
> Thomas
>
>
> On 30/08/2018 16:18, Thomas Lecocq wrote:
> > Sissa,
> >
> > Possible issues:
> >
> > * your new (well, old) data has no network code, or lower case network
> > and/or station code
> >
> > * the component code (channel actually, bad naming in msnoise) is wrong
> >
> > * ...
> >
> > could you send me a dump of the SQL tables (or the sqlite file)
> > directly to my personal email address ?
> >
> > Cheers,
> >
> > Tom
> >
> >
> > On 29/08/2018 18:41, Sigríður Kristjánsdóttir wrote:
> >> Unfortunately this didn´t work.
> >>
> >> I ran
> >>
> >>> msnoise reset DA
> >>> msnoise new_jobs
> >>> msnoise reset CC --all
> >>> msnoise -t 12 compute_cc
> >> and I am still only getting ccftime plots for the old time period.
> >>
> >> Would it be better to start a new project with a new database?
> >>
> >> Sissa
> >>
> >> -----Original Message-----
> >> From: msnoise-bounces at mailman-as.oma.be
> >> <msnoise-bounces at mailman-as.oma.be> On Behalf Of Thomas Lecocq
> >> Sent: miðvikudagur, 29. ágúst 2018 11:23
> >> To: msnoise at mailman-as.oma.be
> >> Subject: Re: [MSNoise] Changing startdate/enddate and ref_begin/ref_end
> >>
> >> Hey,
> >>
> >> it could be the data had been scanned previously and doens't
> >> participate in the New Jobs,
> >>
> >> just do
> >>
> >> msnoise reset DA
> >>
> >> then your workflow should work
> >>
> >> Thomas
> >>
> >>
> >>
> >> Le 29/08/2018 à 13:13, Sigríður Kristjánsdóttir a écrit :
> >>> Hello everyone,
> >>>
> >>> I am trying to run MSNOISE for new startdate/enddate and
> >>> ref_begin/ref_end.
> >>>
> >>> First I changed the relevant parameters in the configuration.
> >>>
> >>> Then I ran msnoise scan_archive.
> >>>
> >>> When I plot the data_availibilty the data shows up on the plot.
> >>>
> >>> Next I ran
> >>>
> >>> msnoise new_jobs
> >>> msnoise reset CC --all
> >>> msnoise -t 10 compute_cc
> >>>
> >>> but when I plot the ccf vs time graphs I only get correlograms for the
> >>> old time period :(
> >>>
> >>> Any ideas what I am missing?
> >>>
> >>> Sissa
> >>>
> >>>     Sigríður Kristjánsdóttir
> >>>
> >>>      Jarðeðlisfræðingur / Geophysicist
> >>>
> >>>      Sími / Tel: +354 528 1608
> >>>
> >>>      Grensásvegur 9, 108 Reykjavík - www.isor.is<http://www.isor.is/>
> >>>      ___________________________________
> >>>
> >>>     [isor-1945-2015]
> >>>
> >>>
> >>>
> >>>
> >>> _______________________________________________
> >>> MSNoise mailing list
> >>> MSNoise at mailman-as.oma.be
> >>> http://mailman-as.oma.be/mailman/listinfo/msnoise
> >> _______________________________________________
> >> MSNoise mailing list
> >> MSNoise at mailman-as.oma.be
> >> http://mailman-as.oma.be/mailman/listinfo/msnoise
> >> _______________________________________________
> >> MSNoise mailing list
> >> MSNoise at mailman-as.oma.be
> >> http://mailman-as.oma.be/mailman/listinfo/msnoise
> >>
> >
>
> --
> Dr. Thomas Lecocq
> Geologist - Seismologist
>
> Seismology - Gravimetry
> Royal Observatory of Belgium
>
>             *
>         * * * * *
>          * * * *
>         ---------
> http://www.seismology.be
> http://msnoise.org
> http://twitter.com/#!/Seismologie_be
> https://www.facebook.com/seismologie.be
>
> _______________________________________________
> MSNoise mailing list
> MSNoise at mailman-as.oma.be
> http://mailman-as.oma.be/mailman/listinfo/msnoise
>